Adhesive residue must be wet scraped to the finished surface of the concrete, leaving only the transparent staining from the glue. Rinse and allow to dry. All Rights Reserved. Mailing Address Custom Building Products 7711 Center Ave. Ste 500 Huntington Beach, CA 92647, © 2021 Custom Building Products. Sheet vinyl must be well bonded and stripped of old finish. Properly installed product requires no special maintenance. Capable of thin-set or medium bed application up to 3/4" (19 mm) thick on horizontal surfaces after beat-in. Never use adhesive removers or solvents, as they soften the adhesive and may cause it to penetrate into the concrete. Refer to the individual product data sheet or packaging directions for application instructions. Mix in a clean bucket at low speed to obtain a lump free solution. Use the following as a guideline. Expansion joints and cold joints, as described in ANSI A108.01, should never be bridged with setting material. The perpendicular motion flattens ridges and closes valleys, allowing maximum coverage. Stir occasionally, but do not add more water. This product contains Portland cement and free silica. SuperiorBilt® Tools are professionally preferred for tile, stone and floor covering installations. Do not use to install resin-backed stone; use EBM-Lite™ Epoxy Bonding Mortar 100% Solids, CEG-Lite™ 100% Solids Commercial Epoxy Grout or contact Custom's® Technical Services for recommendations. (22.68 kg) bag of traditional mortar. The foundation of precise tile and stone setting. Whatever the application, CUSTOM® offers the broadest line of tile and stone setting materials in the industry to give the exact performance your job demands. Custom® Building Products is committed to environmental responsibility in both products produced and in manufacturing practices. Do not breathe dust; wear a NIOSH approved respirator. Apply the primer coat to the floor at a rate of 300 ft2/gal (7.5 M2/L). Stains can RUIN Stone & Tile.Protect Yours Now! ASTM C109 Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in or [50-mm] Cube Specimens), ASTM C627 Standard Test Method for Evaluating Ceramic Floor Tile Installation Systems Using the Robinson-Type Floor Tester, Up to 2 points towards MR Credit 5, Regional Materials, Up to 2 points towards MR Credit 4, Recycled Content, Up to 1 point towards IEQ Credit 4.1, Low-Emitting Materials – Adhesives & Sealants, Vitreous, semi-vitreous and absorptive tile: ceramic, mosaic, quarry, cement body tile, Concrete, mortar beds, masonry, Portland cement plaster, Liquid applied waterproofing membranes such as, Exterior Grade Plywood (interior residential and light commercial dry areas), Fully-bonded sheet vinyl flooring (scarified), Cutback adhesive (see preparation instructions). Wash thoroughly after handling. Dig out any oozing thin-set that you notice. Do not sand or grind adhesive residue, as harmful dust may result. For more information, find details and limitations to this warranty at custombuildingproducts.com. Surfaces to be tiled must be structurally sound and subject to deflection not to exceed the current ANSI Standards. Privacy, Contact | Smooth concrete slabs must be mechanically abraded to achieve proper bond. Let the mixture slake or stand 5 – 10 minutes; stir again and use. If the material has skinned over (not sticky to the touch), recomb with the notch trowel; if too dry, remove and replace the dry material with fresh material. Properly installed tile will last for more than 60 years. Concrete must be cured 28 days and accept water penetration. Expansion joints, perimeter joints and cold joints, as described in ANSI A108.01, should never be bridged with setting material. Protect your surface against both oil-based and water-based stains with the right sealer. Test by sprinkling water on various areas of the substrate. The underlayment must be sufficiently dry and properly cured to the manufacturer’s specifications for permanent, non-moisture permeable coverings. Drying time depends on site conditions, but is normally less than 1 hour. Quality begins from the ground up. Apply a 0.125 in (0.32 cm) layer of thin-set mortar with a flat or square-notched trowel depending on whether you’ll be re-tiling the floor. Call Custom® Technical Services when installing natural stone over plywood subfloor. Expansion joints should never be bridged with setting material. Professional Solutions for Professional Results Submerged applications; wait 14 days after the final grouting period before filing water features with water at 70°F (21°C). Refer to the RFCI Pamphlet, "Recommended Work Practices for Removal of Resilient Floor Coverings", for further information. If water penetrates, then a good bond can be achieved; if water beads, surface contaminants are present, and loss of adhesion may occur. CUSTOM will repair and/or replace, at its discretion, the affected area of the system. This article provides detailed instructions for leveling a subfloor based on our project. Formulated with post-consumer recycled material, it contributes to LEED® certification. The foundation of precise tile and stone setting. Smooth concrete slabs must be mechanically abraded to achieve proper bond. Lightweight or gypsum based underlayments must obtain a minimum 2000 psi (13.8 MP) compressive strength. Mortar thickness should be less than 3/4" when beat in. CustomTech – the industry’s leading collection of technologically-superior, easy-to-use, professional grade subfloor preparation products designed for all types of floor coverings. Custom Building Products: Custom Building Products: Custom Building Products: Custom Building Products: Name: SpeedSet 25 lb. Concrete must be free of efflorescence and not subject to hydrostatic pressure. See TCNA F150-13 tile installations, TCNA F141-13 and F250-13 for stone. Formulated with CustomLite® Technology, ProLite® is 40% lighter than traditional mortars. Obtain the applicable LIMITED PRODUCT WARRANTY at www.custombuildingproducts.com/product-warranty or send a written request to Custom Building Products, Inc., Five Concourse Parkway, Atlanta, GA 30328, USA. Mailing Address Custom Building Products 7711 Center Ave. Ste 500 Huntington Beach, CA 92647, © 2021 Custom Building Products. When properly mixed, troweled ridges will stand without slump. Gray Premixed Thin-Set Mortar: Natural Stone and Large Tile 50 lb. This article is part of our series on How to Install Hardwood Floors. Do not sand flooring that contains asbestos. Stir occasionally, but do not add more water. Contact Custom's Technical Services for the proper treatment of control or saw cut joints. Refer to TCNA EJ171. To determine desirable results, do a test bond area before starting. Mix 5.75 - 6 qts (5.4 - 5.7 L) clean water per 30 lb (13.6 kg) bag of mortar. I am suspecting small amounts of water have no access to the drain weep holes because they are mortared on top of a total hydrobanned surface. Do not bond directly to hardwood, Luan plywood, particle board, parquet, cushion or sponge-back vinyl flooring, metal, fiberglass, plastic or OSB panels. Privacy | Don’t make the mistake of believing that going full-speed is more effective. For more information, find details and limitations to this warranty at custombuildingproducts.com. Sheet vinyl must be well bonded and stripped of old finish. Mix in a clean bucket at low speed to obtain a lump free solution. Use the following as a guideline. Mix by hand or use a low 150 – 200 rpm speed 1/2" (13 mm) drill to achieve a smooth, paste-like consistency. For questions about proper subfloor installation, call Technical Services. Adjust the tile promptly and beat it in with a beating block and rubber mallet. Privacy, Contact | At this point, RedGard can be applied to the primed lightweight or gypsum based surface. Do not breathe dust; wear a NIOSH approved respirator. For tile with longest side 15"+, use a medium bed mortar from CUSTOM designed for large format and heavy tile. Terms | Professional Solutions for Professional Results (13.6 kg) bag covers the same area as a 50 lb. Allow 24 hours before grouting and light traffic. Submerged applications; wait 14 days after the final grouting period before filing water features with water at 70°F (21°C). Terms | CustomTech – the industry’s leading collection of technologically-superior, easy-to-use, professional grade subfloor preparation products designed for all types of floor coverings. Stains on stone, tile or grout happen easily - and can leave permanent stains. Recommended for interior and exterior pools and water features which require ANSI A118.15 bonding mortars. For clear or translucent glass, CUSTOM recommends Glass Tile Premium Thin-Set Mortar. When sanding, an approved respirator should be used. Properly installed product requires no special maintenance. Products : Setting : Polymer-Modified Thin-Set Mortars : FlexBond® Premium Crack Prevention Thin-set Mortar.

Hawaii Chair Gif, Darryl And Dwayne Mooney, Great Value Fish Fillets Cooking Directions, Power Air Fryer Xl Leaking Oil, K2 Mindbender Boot Review, Crime In New Orleans, Division 2 Lady Death Reddit,